Raptor F1 Pro Manual V1.0 Logitech G29 G920 and G923

Raptor F1 Pro — Installation Manual

Raptor Racing

Raptor Mod
F1 Pro 1.0v

Logitech  ·  Installation Manual

Raptor F1 Pro Steering Wheel
Version 1.0  ·  www.RaptoRacing.cl

Content

What platform are you using?

A
Section A
Console — PS4, PS5, Xbox
›
B
Section B
PC — SimHub
›
↺
Additional Information
WiFi Reset
›
⇄
Additional Information
Mode Change
›
◈
Extras
Theme Change
›

Section A

Console Guide

Installation of the Raptor F1 Pro Steering Wheel on PlayStation and Xbox

PS4 PS5 Xbox Series X
1

Step 1

Physical Installation of the Steering Wheel

Replace the original steering wheel of your base with the Raptor F1 Pro Mod. The complete disassembly and assembly process is documented in a video on our YouTube channel.

▶  Watch video on YouTube
2

Step 2

USB Connection

Connect the steering wheel to an available USB port on your console (PS4, PS5, or Xbox). When turned on, the screen will display the Raptor Racing splash screen.

Steering wheel connected — splash screen
Steering wheel splash screen when connecting USB
💡
On PC
Preferably use a USB 3.0 port located at the back of the case for greater stability.
3

Step 3

Screen WiFi Configuration

The screen needs to connect to your WiFi network to receive telemetry. Follow these steps from your phone:

  1. 1 Open your phone's WiFi and search for the network "RaptorF1". Connect to it.
  2. 2 A configuration page will open automatically. If it doesn't appear, open your browser and go to 192.168.4.1
  3. 3 Tap the "Configure WiFi" button.
  4. 4 Select your home network, enter the password, and press Save.
Select RaptorF1 network on phone
Connect to the "RaptorF1" network from your phone
WiFiManager screen 192.168.4.1
WiFiManager Interface at 192.168.4.1
Select home WiFi network
Select your network and save with Save
✅
Successful connection
If everything went well, the steering wheel screen will display the assigned IP address in the upper right corner. Write down that IP.
Steering wheel with assigned IP on screen
The IP appears in the upper right corner of the screen
4

Final Step

In-Game Telemetry Setup

Open Formula 1 2023, 2024, or 2025, go to options and find the UDP Telemetry section. Set the parameters exactly as indicated:

F1 in-game telemetry options
F1 2024 UDP Telemetry Options Menu
Parameter Value
UDP Telemetry On
UDP Broadcast Mode Off
UDP IP Address Screen IP ↗
UDP Port 20777
UDP Send Rate 30 Hz
UDP Format 2024
Your Telemetry Restricted
Show Online ID Off
⚠️
Where do I find the IP?
The IP address appears in the upper right corner of the steering wheel screen once connected to WiFi.
Steering wheel showing IP on screen
IP visible on the steering wheel screen once connected

Additional Information

WiFi Reset

How to reset the connection to change networks

↺

WiFi Reset

Reset Network Connection

The RESET WIFI button on the back allows you to erase the saved network to configure a new one. Use it only when you need to change networks or troubleshoot connectivity issues.

Rear view of the steering wheel — RESET WIFI and THEMES button
Rear view — THEMES button (left) and RESET WIFI button (right)

Steps to Reset

  1. 1Unplug the USB cable from the steering wheel.
  2. 2Press and hold the rear RESET WIFI button.
  3. 3Connect the USB while still pressing the button.
  4. 4Wait for the screen to display the Raptor Racing interface.
  5. 5Release the button and configure a new WiFi network.
🔴
Don't release the button too early
Keep pressing until the screen correctly displays the Raptor Racing interface. The process may take several seconds.

Additional Information

Mode Change

Toggle between Console mode and PC mode

⇄

Mode Change

PC Mode ↔ Console Mode

If you need to switch between Console mode (PS4, PS5, Xbox) and PC mode (SimHub), follow these steps using the large left rear button on the steering wheel:

Steps to change mode

  1. 1Unplug the USB cable from the steering wheel.
  2. 2Press and hold the large left rear button (THEMES).
  3. 3Connect the USB while still pressing the button.
  4. 4The steering wheel will enter setup mode and request WiFi connection.
  5. 5Connect to WiFi following the same setup process (network "RaptorF1" → 192.168.4.1 → Configure WiFi).
  6. 6Upon saving, the steering wheel will automatically change mode.

PC Mode

The screen will display "Waiting for SimHub..." on startup. Requires SimHub to be installed and configured.

Console Mode

The screen will display the Raptor Racing home screen. Compatible with PS4, PS5, and Xbox Series X.

⚠️
Correct button
Make sure to use the large left rear button (THEMES), not the RESET WIFI button which is on the right side.

Section B

PC Guide

Installation with SimHub for maximum computer compatibility

Windows 10 Windows 11 SimHub
1

Step 1

Physical Installation of the Steering Wheel

Replace the original steering wheel of your base with the Raptor F1 Pro Mod. The full video is on our YouTube channel.

▶  Watch video on YouTube
2

Step 2

USB Connection

Connect the steering wheel to a USB 3.0 port on the back of the PC. The screen will display the Raptor Racing logo with the message "Waiting for SimHub..."

Steering wheel waiting for SimHub connection
The steering wheel screen when starting in PC mode — waiting for SimHub
💡
Use the rear ports
The USB ports on the back of the case offer greater stability than the front ones.
3

Step 3

SimHub and Driver Installation

CH341SER driver files
Contents of the driver package
DriverSetup CH341SER installer
Installer — press INSTALL
📦
Correct driver
Select CH341SER.INF in the installer and press INSTALL. The driver corresponds to WCH.CN / USB-Serial CH340.
3.1

Step 3.1

SimHub Configuration

Open SimHub and configure the Arduino to detect the steering wheel:

  1. 1Go to Arduino → My Hardware → Single Arduino
  2. 2Activate "Scan only Selected Ports"
  3. 3Select the COM – USB-Serial CH340 port and press Apply
  4. 4The Raptor F1 Pro v1.0 device will appear. Expand it.
  5. 5Click the EDIT button next to "Custom Protocol"
SimHub Arduino My Hardware
Select COM-CH340 port in SimHub
Raptor F1 Pro device detected
Raptor F1 Pro v1.0 detected — click EDIT
3.2

Step 3.2

Load Communication Protocol

This file tells SimHub what data to send to the steering wheel screen.

↓  Download Communication Protocol
  1. 1Download the protocol file using the button above.
  2. 2Unzip and open the .TXT file.
  3. 3Select all (Ctrl+A) and copy (Ctrl+C).
  4. 4Go back to SimHub and paste the code into the "Protocol Message Binding" window.
  5. 5Click OK, then Apply Changes and Apply.
Protocol .TXT file
Protocol content — select all and copy
Protocol Message Binding in SimHub
Protocol Message Binding window in SimHub
Code pasted in SimHub
Protocol pasted — Raw result visible below
Apply Changes in SimHub
Click Apply Changes to save
✅
Verification
In the "Raw result" panel, you will see a string of numerical data — this confirms that communication is active and working correctly.
★

Final Step

Import RGB LED Profile

Import the pre-configured Raptor Racing profile to activate all visual functions of the steering wheel LEDs.

Center LEDs

RPM indicator and Pit Limiter warning.

Side LEDs

Warnings for nearby cars and flags: yellow, green, red, blue, and black.

↓  Download Raptor F1 Pro v1.0 LED Profile
  1. 1Go to Arduino → RGB Leds → Profiles Manager
  2. 2Click on Import Profile
  3. 3Load the downloaded .ledsprofile file.
SimHub RGB Leds Profiles Manager
RGB Leds Section → Profiles Manager
Import LED profile
Import Profile — load Raptor Racing profile
💡
Recommended LED power
Set the intensity between 10% and 30% for an optimal experience without glare during sessions.

Extras

Theme Change

Customize your steering wheel display with a single button

◈

Customization

Raptor Racing Theme Gallery

The steering wheel includes 2 pre-installed visual themes. Switch between them by pressing the THEMES button on the back of the steering wheel at any time.

Display theme 1
Theme 1 — View with sidebars and lap times
Display theme 2
Theme 2 — View with RPM, gear, and telemetry data
Rear view — THEMES and RESET WIFI button
THEMES button (rear left) to change the visual theme
🔮
More themes coming soon
We will continue to add new themes and layouts. Keep your firmware updated from www.RaptoRacing.cl to access new features.